CAN YOU GIVE ME A LIFT, DAWG?

off road 4WD 4x4 magazine Figure 1

Originally Published in Issue 35 of 4Low Magazine

Make sure to subscribe to get the newest issues of 4Low Magazine right to your mailbox. CLICK HERE

By Christian Sturtz, [email protected]

Photos by Christian Sturtz

Broken parts can ruin any off-road adventure. Motor mounts take a beating, and when they fail, it is often catastrophic. When motor mounts fail, the motor can drop, causing the oil filter to crush and the engine to pump all the oil out in a matter of seconds. The engine falling can also break the fan, shroud, and ruin the radiator.

On the flip side, a broken motor mount can also cause the engine to torque upwards. That exact scenario happened recently while out on the trail with a CJ-7. Sometime during the trip, the driver’s side motor mount broke. This break allowed the motor to lift 1″-3″, even under moderate load, on the driver’s side. The trails involved pretty rough terrain, which didn’t help the problem. The CJ was equipped with an electric fan setup, which relieved one of the potential problems. However, torque of the motor, due to the broken motor mount, was causing the automatic transmission to change gears under load. The torqueing of the engine also kept breaking the vacuum hose on the brake booster, causing a massive vacuum leak, which made the engine die. Due to the rough terrain, this could have put us in some compromising situations.

In this article, we will install heavy-duty motor mounts and a block bracket kit (Part # C2883-1) by Brown Dog Offroad. Brown Dog Offroad products are built in Queen Creek, AZ, and when you call you, you actually talk to the owner in person, which is a huge deal these days! Brown Dog Offroad makes motor mounts and block brackets for YJ, XJ, MJ, and TJ models. They also offer their motor mount in several heights and options; the two different mount constructions are rubber or polyurethane. Brown Dog Offroad also makes OEM height/lifted replacement motor mounts if the bracket system is not in your budget.

off road 4WD 4x4 magazine Figure 1
As soon as you open the box, you can immediately see the quality of these products. From the way they are packaged to the well-labeled hardware bags- Brown Dog Offroad includes a very well put together, full color, set of detailed instructions that contain helpful tips.

The directions suggest you begin on the driver’s side, which locates the engine position. We started by supporting the engine with a floor jack and small piece of wood to spread the load of the jack’s pad across the width of the pan (so the pan doesn’t dent). Then, we loosened all of the bolts on both of the original motor mounts to give us more free play. Next, the mounting bolts (block to bracket and bolt/nut for motor mount) were completely removed. You also have to remove a short bolt that holds the O2 sensor harness bracket. Finally, the driver side motor mount was removed as an assembly.

off road 4WD 4x4 magazine Figure 2
We would suggest while the motor mounts are removed that you run a thread chaser or tap through the holes. The original motor mounts only use three mounting holes on the driver’s and passenger’s side, for a total of six holes. The Brown Dog mounts use seven holes on the driver’s side and six on the passenger side, which means there will be several holes that have never had a bolt in them (be sure to reference the directions for the correct hole size locations). Unfortunately, we didn’t do this step and had problems with one bolt on each side so, we had to run a tap through after the mount was in place.
off road 4WD 4x4 magazine Figure 3
To start the driver’s side install, the directions suggest you mount the motor mount to the block bracket and install it just like it was removed. There are specific instructions on how to tighten the through bolt in the motor mount; at this step, we just barely snugged it up. The new mount and bracket were rotated up, into place, all the bolts were lightly coated with thread lock and then tightened loosely. We had to adjust the jack some to get the motor to the correct height because the new mounts are 1” over stock height.

Both sides use different bolts in different locations. We took a moment to look at the directions and mark the new bolt locations.

off road 4WD 4x4 magazine Figure 4
One of the passenger side bolts is not removable with the motor mount in place. So, we completely removed it first, but even with the motor mount not in place the engine’s height had to be adjusted to remove all of the block mount bolts.
off road 4WD 4x4 magazine Figure 5
Then the new block mount was positioned in place, bolts were lightly coated with thread lock and loosely started into the correct locations. Then we torqued all the block to bracket bolts on both sides (reference directions for spec on your application). We installed the passenger side motor mount. Finally, the motor mount bolts and cross bolts were tightened per directions. Make sure there is no tension on the jack during final motor mount tightening as this could lead to premature failure.
off road 4WD 4x4 magazine Figure 6
We chose to place a small piece of rubber fuel hose over the transmission cooler hose to protect it from rubbing against the head of one of the new bolts. As you can see in the pictures, the motor mounts are top quality products and have great fitment. It is not necessary to remove fenders or nonrelated parts for install; we only did this because we were working on other parts, and it gave a better view of the passenger side install.

Sources:
Brown Dog Offroad
19349 E. Germann Rd, Ste 3
Queen Creek, AZ 85142
866-401-3877
www.browndogindustries.com 

Part used:
Brown Dog Part # C2883-1
GearWrench
Apex Tool Group
910 Ridgebrook Rd, Ste 200
Sparkes, MD 21152
800-688-8949
www.gearwrench.com

This site uses cookies to offer you a better browsing experience. By browsing this website, you agree to our use of cookies.